IMPORTANT! The latest Nvidia drivers for Windows 10 460.79 cause crash when PhoenixMiner starts. The problem is caused by a corrupted DLL file that is installed by the driver.
IMPORTANT! Ethereum Classic (ETC) network switched to a modified version of ethash, called ETCHash. If you are mining ETC you must upgrade to PhoenixMiner 5.3b or later, otherwise you will get only rejected shares when mining ETC.
The current ETC DAG is 195 instead of 390, with corresponding "shrinking" of the DAG buffer to about 2.5 GB. With this DAG size you will be able to mine with 3GB and 4GB cards without problems. After that, each DAG epoch on the ETC network will be twice as long, so the DAG size will grow with half the speed as before. As a result, it will be possible to mine ETC with 4GB cards for about 4 more years.
The switch went without problems, all our test rigs switched to the new DAG and are mining normally. You may need to run auto-tuning again if to get an optimal speed with the new DAG size.
IMPORTANT! All owners of AMD cards with 6 GB or 8 GB RAM must either keep drivers 20.4.x or lower (do not upgrade to 20.5.1 or later), or upgrade to PhoenixMiner 5.2e or later version to continue mining after DAG epoch 384 (ETH will pass it before the end of 2020).
IMPORTANT! All owners of AMD cards with 4 GB RAM must upgrade to PhoenixMiner 5.2e or later version to continue mining after DAG epoch 373. Additionally, here are some important tips for longest possible usage of 4 GB AMD cards with PhoenixMiner 5.2e and later:
Changes in version 5.3b (since 5.2e):
NOTE: If you do not intend to mine Ethereum Classic (ETC) you can stay on PhoenixMiner 5.2e for now because there are no other significant changes besides the support for ETCHash. Please let us know if you have any problems or questions related to PhoenixMiner 5.3b.
PhoenixMiner is fast (arguably the fastest) Ethash (ETH, ETC, Muiscoin, EXP, UBQ, etc.) miner that supports
both AMD and Nvidia cards (including in mixed mining rigs). It runs under Windows x64 and Linux x64
and has a developer fee of 0.65% (the lowest in the industry). This means that every 90
minutes the miner will mine for us, its developers, for 35 seconds.
PhoenixMiner also supports ETCHash for mining ETC, Ubqhash for mining UBQ, ProgPOW for mining BCI, and dual mining
Ethash/Ubqhash with Blake2s.
The speed is generally faster than Claymore's Ethereum miner in eth only mode
(we have measured about 0.4-1.3% speed improvement but your results may be slightly lower or
higher depending on the GPUs). To achieve highest possible speed on AMD cards it may be needed
to manually adjust the GPU tune factor (a number from 8 to about 400, which can be changed
interactively with the + and - keys while the miner is running).
If you have used Claymore's Dual Ethereum miner, you can switch to PhoenixMiner with
minimal hassle as we support most of Claymore's command-line options and confirguration
files.
Easy Plug&Play OS Linux with our miner: https://SimpleMining.net
Please note that PhoenixMiner is extensively tested on many mining rigs but there still may be some bugs.
Additionally, we are actively working on bringing many new features in the future releases.
If you encounter any problems or have feature requests, please post them here (in this thread).
We will do our best to answer in timely fashion.
Screenshot:
1. Quick start
You can download PhoenixMiner 5.3b from here:
https://www.sendspace.com/folder/ugy44z
Examples of settings for different pools.
ethermine org (ETH):
PhoenixMiner.exe -pool eu1 ethermine org:4444 -pool2 us1 ethermine org:4444 -wal YourEthWalletAddress.WorkerName -proto 3
ethermine org (ETH, secure connection):
PhoenixMiner.exe -pool ssl: //eu1 ethermine org: 5555 -pool2 ssl: //us1 ethermine org: 5555 -wal YourEthWalletAddress.WorkerName -proto 3
ethpool org (ETH):
PhoenixMiner.exe -pool eu1 ethpool org:3333 -pool2 us1 ethpool org:3333 -wal YourEthWalletAddress.WorkerName -proto 3
dwarfpool com (ETH):
PhoenixMiner.exe -pool eth-eu dwarfpool com:8008 -wal YourEthWalletAddress / WorkerName -pass x
nanopool org (ETH):
PhoenixMiner.exe -pool eu1 nanopool org:9999 -wal YourEthWalletAddress / WorkerName -pass x
nicehash (ethash):
PhoenixMiner.exe -pool stratum + tcp: //daggerhashimoto eu nicehash com: 3353 -wal YourBtcWalletAddress -pass x -proto 4 -stales 0
f2pool (ETH):
PhoenixMiner.exe -epool eth f2pool com:8008 -ewal YourEthWalletAddress -pass x -worker WorkerName
miningpoolhub (ETH):
PhoenixMiner.exe -pool us-east ethash-hub miningpoolhub com:20535 -wal YourLoginName.WorkerName -pass x -proto 1
coinotron com (ETH):
PhoenixMiner.exe -pool coinotron com:3344 -wal YourLoginName.WorkerName -pass x -proto 1
ethermine org (ETC):
PhoenixMiner.exe -pool eu1-etc ethermine org:4444 -wal YourEtcWalletAddress.WorkerName
dwarfpool com (EXP):
PhoenixMiner.exe -pool exp-eu dwarfpool com:8018 -wal YourExpWalletAddress / WorkerName
miningpoolhub (MUSIC):
PhoenixMiner.exe -pool europe ethash-hub miningpoolhub com:20585 -wal YourLoginName.WorkerName -pass x -proto 1
ubiqpool (UBIQ):
PhoenixMiner.exe -pool stratum + tcp: //eu ubiqpool io: 8008 -wal YourUbiqWalletAddress -pass x -worker WorkerName
minerpool net (PIRL):
PhoenixMiner.exe -pool pirl minerpool net:8002 -wal YourPirlWalletAddress -pass x -worker WorkerName
dodopool com (Metaverse ETP):
PhoenixMiner.exe -pool etp dodopool com:8008 -wal YourMetaverseETPWalletAddress -worker Rig1 -pass
minerpool net (Ellaism):
PhoenixMiner.exe -pool ella minerpool net:8002 -wal YourEllaismWalletAddress -worker Rig1 -pass x
Pool options:
3. Command-line arguments
Note that PhoenixMiner supports most of the command-line options of Claymore's dual Ethereum miner
so you can use the same command line options as the ones you would have used with Claymore's miner.
-pool <host rt> Ethash pool address (prepend the host name with ssl:// for SSL pool, or http:// for solo mining)
-wal <wallet> Ethash wallet (some pools require appending of user name and/or worker)
-pass <password> Ethash password (most pools don't require it, use 'x' as password if unsure)
-worker <name> Ethash worker name (most pools accept it as part of wallet)
-proto <n> Selects the kind of stratum protocol for the ethash pool:
1: miner-proxy stratum spec (e.g. coinotron)
2: eth-proxy (e.g. dwarfpool, nanopool) - this is the default, works for most pools
3: qtminer (e.g. ethpool)
4: EthereumStratum/1.0.0 (e.g. nicehash)
5: EthereumStratum/2.0.0
-coin <coin> Ethash coin to use for devfee to avoid switching DAGs:
auto: Try to determine from the pool address (default)
eth: Ethereum
etc: Ethereum Classic
exp: Expanse
music: Musicoin
ubq: UBIQ
pirl: Pirl
ella: Ellaism
etp: Metaverse ETP
pgc: Pegascoin
akroma: Akroma
whale: WhaleCoin
vic: Victorium
nuko: Nekonium
mix: Mix
egem: EtherGem
aura: Aura
hbc: Hotelbyte Coin
gen: Genom
etz: EtherZero
clo: Callisto
dbix: DubaiCoin
moac: MOAC
etho: Ether-1
etcc: EtherCC
yoc: Yocoin
b2g: Bitcoiin2Gen
esn: Ethersocial
ath: Atheios
reosc: REOSC
4. Configuration files
Note that PhoenixMiner supports the same configuration files as Claymore's dual Ethereum miner
so you can use your existing configuration files without any changes.
Instead of using command-line options, you can also control PhoenixMiner with configuration
files. If you run PhoenixMiner.exe without any options, it will search for the file config.txt
in the current directory and will read its command-line options from it. If you want, you can
use file with another name by specifying its name as the only command-line option
when running PhoenixMiner.exe.
You will find an example config.txt file in the PhoenixMiner's directory.
Instead of specifying the pool(s) directly on the command line, you can use another configuration
file for this, named epools.txt. There you can specify one pool per line (you will find an example
epools.txt file in the PhoenixMiner's directory).
For the dual mining pools, you can use the dpools.txt file, which has the same format as epools.txt
but for the secondary coin. You will find an example epools.txt file in the PhoenixMiner's directory.
Note that unlike the epools.txt, which is loaded each time when the miner starts, the dpools.txt file
is only read if you specify a dual mining pool on the command line with -dpool, or at least add
the -dcoin blake2s command-line option.
The advantages of using config.txt and epools.txt/dpools.txt files are:
- If you have multiple rigs, you can copy and paste all settings with these files
- If you control your rigs via remote control, you can change pools and even the miner options by
uploading new epools.txt files to the miner, or by uploading new config.txt file and restarting
the miner.
5. Remote monitoring and management
Phoenix miner is fully compatible with Claymore's dual miner protocol for remote monitoring and
management. This means that you can use any tools that are build to support Claymore's dual miner,
including the "Remote manager" application that is part of Claymore's dual miner package.
We are working on much more powerful and secure remote monitoring and control functionality and
control center application, which will allow better control over your remote or local rigs and some
unique features to increase your mining profits.
IMPORTANT! Ethereum Classic (ETC) network switched to a modified version of ethash, called ETCHash. If you are mining ETC you must upgrade to PhoenixMiner 5.3b or later, otherwise you will get only rejected shares when mining ETC.
The current ETC DAG is 195 instead of 390, with corresponding "shrinking" of the DAG buffer to about 2.5 GB. With this DAG size you will be able to mine with 3GB and 4GB cards without problems. After that, each DAG epoch on the ETC network will be twice as long, so the DAG size will grow with half the speed as before. As a result, it will be possible to mine ETC with 4GB cards for about 4 more years.
The switch went without problems, all our test rigs switched to the new DAG and are mining normally. You may need to run auto-tuning again if to get an optimal speed with the new DAG size.
IMPORTANT! All owners of AMD cards with 6 GB or 8 GB RAM must either keep drivers 20.4.x or lower (do not upgrade to 20.5.1 or later), or upgrade to PhoenixMiner 5.2e or later version to continue mining after DAG epoch 384 (ETH will pass it before the end of 2020).
IMPORTANT! All owners of AMD cards with 4 GB RAM must upgrade to PhoenixMiner 5.2e or later version to continue mining after DAG epoch 373. Additionally, here are some important tips for longest possible usage of 4 GB AMD cards with PhoenixMiner 5.2e and later:
Changes in version 5.3b (since 5.2e):
- Added support for the new ETCHash algorithm that is used by the ETC blockchain from Nov 28, 2020. If you want to mine ETC, you should add -coin etc to your command-line, or , COIN: etc to your epools.txt file. See the start_miner_etc.bat and epools_example.txt files for examples
NOTE: If you do not intend to mine Ethereum Classic (ETC) you can stay on PhoenixMiner 5.2e for now because there are no other significant changes besides the support for ETCHash. Please let us know if you have any problems or questions related to PhoenixMiner 5.3b.
PhoenixMiner is fast (arguably the fastest) Ethash (ETH, ETC, Muiscoin, EXP, UBQ, etc.) miner that supports
both AMD and Nvidia cards (including in mixed mining rigs). It runs under Windows x64 and Linux x64
and has a developer fee of 0.65% (the lowest in the industry). This means that every 90
minutes the miner will mine for us, its developers, for 35 seconds.
PhoenixMiner also supports ETCHash for mining ETC, Ubqhash for mining UBQ, ProgPOW for mining BCI, and dual mining
Ethash/Ubqhash with Blake2s.
The speed is generally faster than Claymore's Ethereum miner in eth only mode
(we have measured about 0.4-1.3% speed improvement but your results may be slightly lower or
higher depending on the GPUs). To achieve highest possible speed on AMD cards it may be needed
to manually adjust the GPU tune factor (a number from 8 to about 400, which can be changed
interactively with the + and - keys while the miner is running).
If you have used Claymore's Dual Ethereum miner, you can switch to PhoenixMiner with
minimal hassle as we support most of Claymore's command-line options and confirguration
files.
Easy Plug&Play OS Linux with our miner: https://SimpleMining.net
Please note that PhoenixMiner is extensively tested on many mining rigs but there still may be some bugs.
Additionally, we are actively working on bringing many new features in the future releases.
If you encounter any problems or have feature requests, please post them here (in this thread).
We will do our best to answer in timely fashion.
Screenshot:
1. Quick start
You can download PhoenixMiner 5.3b from here:
https://www.sendspace.com/folder/ugy44z
Examples of settings for different pools.
ethermine org (ETH):
PhoenixMiner.exe -pool eu1 ethermine org:4444 -pool2 us1 ethermine org:4444 -wal YourEthWalletAddress.WorkerName -proto 3
ethermine org (ETH, secure connection):
PhoenixMiner.exe -pool ssl: //eu1 ethermine org: 5555 -pool2 ssl: //us1 ethermine org: 5555 -wal YourEthWalletAddress.WorkerName -proto 3
ethpool org (ETH):
PhoenixMiner.exe -pool eu1 ethpool org:3333 -pool2 us1 ethpool org:3333 -wal YourEthWalletAddress.WorkerName -proto 3
dwarfpool com (ETH):
PhoenixMiner.exe -pool eth-eu dwarfpool com:8008 -wal YourEthWalletAddress / WorkerName -pass x
nanopool org (ETH):
PhoenixMiner.exe -pool eu1 nanopool org:9999 -wal YourEthWalletAddress / WorkerName -pass x
nicehash (ethash):
PhoenixMiner.exe -pool stratum + tcp: //daggerhashimoto eu nicehash com: 3353 -wal YourBtcWalletAddress -pass x -proto 4 -stales 0
f2pool (ETH):
PhoenixMiner.exe -epool eth f2pool com:8008 -ewal YourEthWalletAddress -pass x -worker WorkerName
miningpoolhub (ETH):
PhoenixMiner.exe -pool us-east ethash-hub miningpoolhub com:20535 -wal YourLoginName.WorkerName -pass x -proto 1
coinotron com (ETH):
PhoenixMiner.exe -pool coinotron com:3344 -wal YourLoginName.WorkerName -pass x -proto 1
ethermine org (ETC):
PhoenixMiner.exe -pool eu1-etc ethermine org:4444 -wal YourEtcWalletAddress.WorkerName
dwarfpool com (EXP):
PhoenixMiner.exe -pool exp-eu dwarfpool com:8018 -wal YourExpWalletAddress / WorkerName
miningpoolhub (MUSIC):
PhoenixMiner.exe -pool europe ethash-hub miningpoolhub com:20585 -wal YourLoginName.WorkerName -pass x -proto 1
ubiqpool (UBIQ):
PhoenixMiner.exe -pool stratum + tcp: //eu ubiqpool io: 8008 -wal YourUbiqWalletAddress -pass x -worker WorkerName
minerpool net (PIRL):
PhoenixMiner.exe -pool pirl minerpool net:8002 -wal YourPirlWalletAddress -pass x -worker WorkerName
dodopool com (Metaverse ETP):
PhoenixMiner.exe -pool etp dodopool com:8008 -wal YourMetaverseETPWalletAddress -worker Rig1 -pass
minerpool net (Ellaism):
PhoenixMiner.exe -pool ella minerpool net:8002 -wal YourEllaismWalletAddress -worker Rig1 -pass x
Pool options:
3. Command-line arguments
Note that PhoenixMiner supports most of the command-line options of Claymore's dual Ethereum miner
so you can use the same command line options as the ones you would have used with Claymore's miner.
-pool <host rt> Ethash pool address (prepend the host name with ssl:// for SSL pool, or http:// for solo mining)
-wal <wallet> Ethash wallet (some pools require appending of user name and/or worker)
-pass <password> Ethash password (most pools don't require it, use 'x' as password if unsure)
-worker <name> Ethash worker name (most pools accept it as part of wallet)
-proto <n> Selects the kind of stratum protocol for the ethash pool:
1: miner-proxy stratum spec (e.g. coinotron)
2: eth-proxy (e.g. dwarfpool, nanopool) - this is the default, works for most pools
3: qtminer (e.g. ethpool)
4: EthereumStratum/1.0.0 (e.g. nicehash)
5: EthereumStratum/2.0.0
-coin <coin> Ethash coin to use for devfee to avoid switching DAGs:
auto: Try to determine from the pool address (default)
eth: Ethereum
etc: Ethereum Classic
exp: Expanse
music: Musicoin
ubq: UBIQ
pirl: Pirl
ella: Ellaism
etp: Metaverse ETP
pgc: Pegascoin
akroma: Akroma
whale: WhaleCoin
vic: Victorium
nuko: Nekonium
mix: Mix
egem: EtherGem
aura: Aura
hbc: Hotelbyte Coin
gen: Genom
etz: EtherZero
clo: Callisto
dbix: DubaiCoin
moac: MOAC
etho: Ether-1
etcc: EtherCC
yoc: Yocoin
b2g: Bitcoiin2Gen
esn: Ethersocial
ath: Atheios
reosc: REOSC
4. Configuration files
Note that PhoenixMiner supports the same configuration files as Claymore's dual Ethereum miner
so you can use your existing configuration files without any changes.
Instead of using command-line options, you can also control PhoenixMiner with configuration
files. If you run PhoenixMiner.exe without any options, it will search for the file config.txt
in the current directory and will read its command-line options from it. If you want, you can
use file with another name by specifying its name as the only command-line option
when running PhoenixMiner.exe.
You will find an example config.txt file in the PhoenixMiner's directory.
Instead of specifying the pool(s) directly on the command line, you can use another configuration
file for this, named epools.txt. There you can specify one pool per line (you will find an example
epools.txt file in the PhoenixMiner's directory).
For the dual mining pools, you can use the dpools.txt file, which has the same format as epools.txt
but for the secondary coin. You will find an example epools.txt file in the PhoenixMiner's directory.
Note that unlike the epools.txt, which is loaded each time when the miner starts, the dpools.txt file
is only read if you specify a dual mining pool on the command line with -dpool, or at least add
the -dcoin blake2s command-line option.
The advantages of using config.txt and epools.txt/dpools.txt files are:
- If you have multiple rigs, you can copy and paste all settings with these files
- If you control your rigs via remote control, you can change pools and even the miner options by
uploading new epools.txt files to the miner, or by uploading new config.txt file and restarting
the miner.
5. Remote monitoring and management
Phoenix miner is fully compatible with Claymore's dual miner protocol for remote monitoring and
management. This means that you can use any tools that are build to support Claymore's dual miner,
including the "Remote manager" application that is part of Claymore's dual miner package.
We are working on much more powerful and secure remote monitoring and control functionality and
control center application, which will allow better control over your remote or local rigs and some
unique features to increase your mining profits.
Son düzenleme: